Hydro-Temp's 
Residential Products and Options
Complete Product Manual available upon request

WATER SOURCE HEAT PUMPS

ULTRAVIOLET AIR PURIFYING SYSTEM

ELECTROSTATIC AIR FILTERS

RADIANT HEATING SYSTEMS

POOL HEATERS

DEHUMIDIFIERS

 

WATER SOURCE HEAT PUMPS (Standard Heat and Air):

Available in 1/2 ton increments from 1 to 50 tons. 

Compressor Options: Single or Dual.

Water Source Option: Well Water or Closed Loop.

Coil Size Options: Standard or Oversized.

Zone Damper Controller: (Standard on most systems)

Hot Water Heating Options: Desuperheater or Priority.

Configuration Options: Vertical, Horizontal, or Split.

Air Flow Direction: Up-flow, Horizontal Flow, or Counter Flow.

Variable Speed Blower: Programmable ECM Blower to Match compressor speeds.

Strip Heat Options: 5 KW or 10 KW.

KWH meter: Standard Equipment

Thermostat Options



Back to Top of Page

Compressor Options:

-Single Compressor: A single compressor system normally includes a single Bristol Compressor. In 1993, Hydro-Temp began producing all of its units with the Bristol Compressors.  A hermetically sealed compressor with internal thermal protection, this compressor was selected over the reciprocating compressor because of its reliability, heating capacity, and efficiency.

-Dual Compressors:  A dual compressor system normally consists of both a small and a large Bristol Compressor.  This unique design allows the unit to provide three stages of heating and cooling:  stage one uses only the small compressor, stage two uses only the large compressor, and stage three employs both compressors at the same time.  Dual compressors run on the same refrigeration circuit, allowing the small and large compressor to run on coils sized for both compressors -- resulting in increased efficiency.  Hydro-Temp Corporation is the only manufacturer in the United States to produce a three stage ground source heat pump.  The unit's capacity will vary depending upon a particular structure's needs.  The three stage unit is particularly suited large homes where different loads are required for different zones.  For example in the cooling mode the zones on the upper floors will require more cooling then the lower zones or basement zones.  This type of unit has provided electric utilities with a system that is beneficial to their load control programs and customers with the most efficient heating and cooling system on the market today.

Back to Heat Pump Options

Water Source Options:

-Well Water System: A well water system uses ground water at an approximate temperature of 55 to 60° F as a heat exchange medium.  At this temperature, the system uses approximately one gallon of water per ton of equipment.  A Hydro-Temp unit will absorb heat from the water when in the heating mode and transfer heat to the water when in the cooling mode.  To conserve water while saving the customer money, the pressure regulating water valves shut the water off when not in use.  When employing this type of system, it is necessary to have a quality water source capable of meeting your particular application's water demand needs.

-Closed Loop System: A closed loop system requires approximately 500 feet of high-density polyethylene pipe per ton of equipment to be buried six feet under the ground.  If space is a problem, these loops may be buried vertically by drilling straight down to a depth that will depend upon the location's geology.  Once the pipe has been installed, it is then filled with a water and antifreeze solution, which will be circulated over and over again by a 1/6 horsepower pump.  A common problem with this type of system is that, after operating for a few days, air trapped within the loop works its way up to the system's highest point--the pump.  As a result, the pump will air lock and quickly burn out.  Fortunately, Hydro-Temp has been able to eradicate this problem through the use of an auto purge system, which purges the air out of the closed loop before it enters the pump. 

-Lake or Pond Loop: The lake or pond loop is an available option for those employing a closed loop system.  In this application, a 500 foot roll of high density polyethylene pipe per ton of equipment is tied to cinder blocks and sunk to the bottom of the lake or pond.  Typically, one roll of pipe per ton is needed.  Each roll is tied to a pipe or rail to keep them together and the ties are cut so that they will spread apart.  The recommended depth of the lake will vary, depending upon the location's geology. 

 NOTE:  In general, no one water source is better than another.  When considering a Hydro-Temp unit, the important question to ask is, "Which application is the most practical for me?"

Back to Heat Pump Options

--Coil Size Options:  For years, Hydro-Temp Corporation has manufactured extremely efficient heating and cooling systems by over-sizing the water and air coils by one size.  For example, if a customer purchased a four ton unit, we installed five ton heat exchangers.  We have since discovered that even greater efficiency can be produced by over-sizing the heat exchangers by two sizes--installing six ton heat exchangers with the four ton unit.  With more surface area on the air coil, there is more heat transfer and dehumidification in the air conditioning mode.  Our standard option provides the customer with heat exchangers that are one ton larger than the unit, while the over-sized option offers heat exchangers that are two tons larger.

Back to Heat Pump Options

Hot Water Heating Options:

Hydro-Temp systems can efficiently meet your home's hot water needs by employing one of two different options available to the homeowner:

  -Desuperheater:  While heating and cooling, the desuperheater can normally meet the hot water needs of a couple of people for free in the summer and at a very low cost in the winter.  Even if a desuperheater cannot keep up with a home's usage it can assist the hot water tank in efficiently heating the water.

-Priority Hot Water:  The priority hot water heating option is a patented system that works like a desuperheater  except that, once the heating or cooling load from the house is satisfied, the units microprocessor can turn on the system just to heat hot water if needed.  The temperature of the hotwater tank is monitored by a digital aqua stat installed when the system is installed. When the room thermostat later calls for more heating or cooling, the unit will then switch back and heat or cool the home.  The breaker to the hot water tank is turned off as this system will provide 100% of a household's hot water needs. 
Some of the advanced features of the Priority system include the ability to extract heat from the home and put the heat into the hot water tank by turning off the ground loop or well water when cooling for the house is needed at the same time the aqua stat calls for hot water heating.

More water heating tips and drawings.

Back to Heat Pump Options

Zone Control: Zone control, or dampering of zones, can be accomplished with the addition of a microprocessor control board to the Hydro-Temp system.  The microprocessor is now coming standard on most equipment. Each zone will have its on zone damper and thermostat that hooks directly to the control board inside the Hydro-Temp System.  The control board will then open and close the proper dampers and turn on and off the Hydro-Temp unit.  The control board will allow for some thermostats to call for heat while others can call for cool.  The microprocessor will open the zones calling for heating and turn on the Hydro-Temp system in heat mode.  All zones calling for cool or not calling at all will close their dampers.  When the heating call is satisfied the zones calling for heat will close their dampers and the zones calling for cool will open their dampers and switch the system to cool mode.  (Heating always gets top priority) This allows a 4 zone system to work as if it has 4 units installed.  This set up is ideal for multi-level homes or for separating bedrooms from the rest of the house.  Also used in most commercial buildings and schools.

The control board usually handles four zones, but has the capability of managing up to twelve zones.  Zone control is compatible with all other options available to the Hydro-Temp system.
 
Back to Top of Page

Electrostatic Air filters: Hydro-Temp Corporation manufactures an electrostatic air filter that actually purifies the air you breathe as it attracts and holds millions of airborne pollutants, such as dust, pollen, mold spores, animal dander, smoke, and household chemicals.  The filter's electrostatically charged fibers are activated by the air passing through them and an added layer of charcoal (available upon request) between the polypropylene fibers is especially effective in removing stubborn odors.  Maintenance for the filter is simple--just snap it out and back wash it periodically to remove build-up.  The electrostatic air filter easily fits into the original filter space of an existing unit, requiring no additional ductwork or wiring.  The filter may be purchased individually or with a new unit. 


|Pricing and Ordering information|

Back to Top of Page

Variable Speed Blower: Hydro-Temp redefines comfort and efficiency by incorporating GE ECM^TM Blower Motor Technology in our equipment. These systems feature: more even temperatures, better indoor air quality, precise humidity control, quieter operation and lower utility bills.

Features and Benefits of the ECM 2.3

• Ultra-high efficiency
  ECM 2.3 efficiencies are as high as 82%. At full load the ECM 2.3 is 20% more efficient than a standard induction motor. At low speed the ECM is over 30% more efficient than a standard induction motor. On constant fan speed, the ECM consumes 60-80 Watts as compared to 400 watts for the induction motor. What's more, its permanent magnet, DC design allows it to maintain its efficiency over its wide speed range.
• Self regulating constant airflow
  Unlike a conventional blower motor, which is designed to operate at one speed, the GE ECM variable -speed motor can run in a wide range of speeds. That's important because blowers need to adjust speed to deliver the airflow needed by the system. GE's patented constant airflow technology can be programmed to deliver constant airflow into a wide range of external static pressures in an air distribution system. This is all accomplished without the use of external sensors. Some benefits of constant airflow: precise air flow for multi stage equipment, improved air distribution throughout the static pressure range, improved indoor air quality with the use of high efficiency air filters and low speed constant fan operation which not only saves money but lessens the temperature stratification that can be common in multilevel homes.
• Low Audible noise
  The most frequent praise given ECM powered systems by customers is how quiet they are. The GE patented resilient rotor construction effectively eliminates noise transmitted through the shaft. The ECM's ability to be programmed to slowly ramp up to speed eliminates the abrupt change in sound found when an induction motor HVAC system cycles on and off. Hydro-Temp comfort systems are designed to take advantage of the ECM's low speed efficiency at first and second stage operation and continuous fan speeds, further reducing audible noise.

Back to Heat Pump Options
 

KWH Electric Meter: Every Hydro-Temp system sold comes standard with a KWH meter. This meter is identical to the meter most people read on there house every month for the electric company. This meter is installed just to prove the efficiency of the Hydro-Temp system. You should read this meter once a month when you read your meter for the whole house. Then you can tell exactly how much you are spending on heating and cooling your house and heating your hot water. This is our way of proving to you that the unit will do what we said it would do.

Back to Heat Pump Options

Digital Thermostats

Hydro-Temp uses several Digital Thermostats to control the Hydro-Temp system.  All thermostats digitally show the room temperature and desired setting.
Most thermostats are programmable to achieve peak efficiency.  Programmable thermostats can be programmed to change the room temperature while you are gone, then reset the temperature when you return. 

A touch screen 7 day programmable thermostat that almost reads your mind is also available, Honeywell's Vision Thermostat is the easiest-to-use thermostat ever - no owner's manual needed. Its intuitive logic responds to your choices and schedule for optimal comfort and energy savings

Back to Heat Pump Options

Radiant Heating Systems

Over the last couple of years there has been a resurgence in the use of radiant heating to heat homes. Studies have shown time and time again that when radiant heat is available it is the preference of young and old alike because it is the most comfortable type of heat.
In the past if you wanted radiant heat in your home your choice of heating systems was typically some type of fossil fuel boiler. This meant that you had to install a separate system to provide air conditioning.
In 1980, Hydro-Temp was granted a patent for its design of a full condensing on-demand water heating system. This patent enables Hydro-Temp to integrate the traditional forced air systems with one that is suitable for heating large quantities of water. This unit is ideal for applications that want radiant floor heat as well as forced air space conditioning. Using this type of unit generally means dealing with one mechanical contractor to install your heat and air.

Back to Top of Page

Pool Heaters

Hydro-Temp manufactures pool heaters (commonly referred to as water-to-water systems) that range from one to twenty tons in size.  Instead of using the domestic hot water tank, Hydro-Temp uses the priority coil in the standard heat pump to heat the pool.  This method requires the use of cupronickel heat exchangers and is applied when there is more than one unit.  For example, one unit will have the priority heating option to heat the domestic hot water while the other unit heats the pool when not heating or cooling the house.  There are many options available to the homeowner who decides to employ this type of system.

Back to Top of Page

Back to Top of Page

Copyright © 2008 Hydro-Temp Corporation, Inc.